01
Set the target flow
Enter the target flow on the touchscreen; the controller takes it as the speed reference for the drive.
Precision Micro Gear Pump / Flow Control System
Set the flow. Get the flow.
An integrated fluid delivery platform for low-speed, micro-flow duty. Step / servo motor speed control and a bilingual touchscreen turn flow adjustment on a micro gear pump into something simple and deterministic.
Laboratory pilot & bench scale
Closed-loop auto-match
±0.5‰
Dosing precision
50–200 ms
Response time
1:100
Turndown ratio
01 / System Overview
An integrated fluid delivery platform on a single bench
The JONSN micro gear pump flow control system is an integrated fluid delivery platform built for laboratory pilot and bench-scale stages. A filter, high-precision gear pump, servo motor, high-precision flow meter, pressure sensor and valves are all pre-installed inside one desktop cabinet.
Through closed-loop linkage between the flow meter signal and the gear pump servo motor, the system automatically matches set flow to actual flow, and displays online instantaneous flow and pressure fluctuation in real time. Flow control moves from repeated manual valve adjustment to set-and-go. In daily use you only connect the inlet and outlet lines, complete the flow meter parameter setup on the touchscreen, and start — no complex commissioning required.
02 / Closed-Loop Control
How the loop works: set → detect → compare → adjust
Built for conditions where system pressure differential is unstable but flow precision requirements are high. Pressure fluctuation is compensated automatically by the loop, so the flow output stays constant.
02
Detect in real time
The Coriolis mass flow meter measures actual flow continuously and returns the signal to the controller.
03
Compare the deviation
The controller computes the deviation between set flow and measured flow, in real time.
04
Adjust speed automatically
Servo motor speed is corrected until the deviation falls back inside the tolerance band.
Result
Suitable for operating conditions with unstable system differential pressure but high flow-rate accuracy requirements — pressure fluctuations are automatically compensated through closed-loop control, maintaining a constant flow output.
03 / Core Performance
Three numbers that decide whether micro flow is viable
±0.5‰
High-precision delivery
Dosing precision reaches ±0.5‰, meeting metering-class requirements for micro flow.
50–200 ms
Fast response
Response time is only 50–200 ms, so the output follows a process change immediately.
1:100
Wide turndown
A turndown ratio of 1:100 means one unit covers multiple process setpoints.
04 / Main Hardware
Five elements, one cabinet — nothing left to select
JONSN high-precision micro gear pump
The delivery element of the system, metering micro flow at ±0.5‰ precision.
Pressure sensor
Online monitoring of pressure fluctuation, so back pressure stays inside the control band.
Coriolis mass flow meter
The closed-loop feedback signal source, measuring mass flow directly.
Control cabinet with touchscreen
Bilingual Chinese / English interface for parameter setting, display and alarm.
Back-pressure valve
Stabilises back pressure and suppresses pulsation at the delivery line.
Integrated as standard
A filter and valves are integrated into the system, so you do not need to select or source supporting components separately.
05 / Installation & Application
Installed in minutes, applied across precision process industries
Simple installation
The unit is assembled and commissioned before it leaves the factory. You only connect the inlet and outlet lines and power it on.
Place the cabinet on the bench and connect inlet / outlet lines
Power on, set flow meter parameters on the touchscreen
Enter the target flow and start — no on-site tuning
Application industries
Micro flow delivery for processes where the setpoint must hold while pressure moves:
Fine chemicals
Pharmaceutical
Automation equipment
Semiconductor processing
Fuel cell
06 / Technical Parameters
Technical parameters
| Item | Specification |
|---|---|
| Dimensions | 560 × 500 × 800 mm (desktop type) |
| Control method | Step / servo motor speed closed loop |
| Precision | ±0.5‰ |
| Response time | 50–200 ms |
| Turndown ratio | 1:100 |
| Interface | Touchscreen, Chinese / English |
| Application stage | Laboratory pilot / bench scale |
Need multi-component ratio delivery?
In addition to the standard single-component system, JONSN can customize dual-component, tri-component, and multi-component micro-flow control systems according to process requirements, supporting independent closed-loop and synchronized ratio control for each channel.
Customization development is supported for flow range, material, interface type, and communication protocol.
Precision Micro Gear Pump / Flow Control System
Set the flow. Get the flow.
An integrated fluid delivery platform for low-speed, micro-flow duty. Step / servo motor speed control and a bilingual touchscreen turn flow adjustment on a micro gear pump into something simple and deterministic.
Laboratory pilot & bench scale
Closed-loop auto-match
±0.5‰
Dosing precision
50–200 ms
Response time
1:100
Turndown ratio
01 / System Overview
An integrated fluid delivery platform on a single bench
The JONSN micro gear pump flow control system is an integrated fluid delivery platform built for laboratory pilot and bench-scale stages. A filter, high-precision gear pump, servo motor, high-precision flow meter, pressure sensor and valves are all pre-installed inside one desktop cabinet.
Through closed-loop linkage between the flow meter signal and the gear pump servo motor, the system automatically matches set flow to actual flow, and displays online instantaneous flow and pressure fluctuation in real time. Flow control moves from repeated manual valve adjustment to set-and-go. In daily use you only connect the inlet and outlet lines, complete the flow meter parameter setup on the touchscreen, and start — no complex commissioning required.
02 / Closed-Loop Control
How the loop works: set → detect → compare → adjust
Built for conditions where system pressure differential is unstable but flow precision requirements are high. Pressure fluctuation is compensated automatically by the loop, so the flow output stays constant.
01
Set the target flow
Enter the target flow on the touchscreen; the controller takes it as the speed reference for the drive.
02
Detect in real time
The Coriolis mass flow meter measures actual flow continuously and returns the signal to the controller.
03
Compare the deviation
The controller computes the deviation between set flow and measured flow, in real time.
04
Adjust speed automatically
Servo motor speed is corrected until the deviation falls back inside the tolerance band.
Result
Suitable for operating conditions with unstable system differential pressure but high flow-rate accuracy requirements — pressure fluctuations are automatically compensated through closed-loop control, maintaining a constant flow output.
03 / Core Performance
Three numbers that decide whether micro flow is viable
±0.5‰
High-precision delivery
Dosing precision reaches ±0.5‰, meeting metering-class requirements for micro flow.
50–200 ms
Fast response
Response time is only 50–200 ms, so the output follows a process change immediately.
1:100
Wide turndown
A turndown ratio of 1:100 means one unit covers multiple process setpoints.
04 / Main Hardware
Five elements, one cabinet — nothing left to select
JONSN high-precision micro gear pump
The delivery element of the system, metering micro flow at ±0.5‰ precision.
Pressure sensor
Online monitoring of pressure fluctuation, so back pressure stays inside the control band.
Coriolis mass flow meter
The closed-loop feedback signal source, measuring mass flow directly.
Control cabinet with touchscreen
Bilingual Chinese / English interface for parameter setting, display and alarm.
Back-pressure valve
Stabilises back pressure and suppresses pulsation at the delivery line.
Integrated as standard
A filter and valves are integrated into the system, so you do not need to select or source supporting components separately.
05 / Installation & Application
Installed in minutes, applied across precision process industries
Simple installation
The unit is assembled and commissioned before it leaves the factory. You only connect the inlet and outlet lines and power it on.
Place the cabinet on the bench and connect inlet / outlet lines
Power on, set flow meter parameters on the touchscreen
Enter the target flow and start — no on-site tuning
Application industries
Micro flow delivery for processes where the setpoint must hold while pressure moves:
Fine chemicals
Pharmaceutical
Automation equipment
Semiconductor processing
Fuel cell
06 / Technical Parameters
Technical parameters
| Item | Specification |
|---|---|
| Dimensions | 560 × 500 × 800 mm (desktop type) |
| Control method | Step / servo motor speed closed loop |
| Precision | ±0.5‰ |
| Response time | 50–200 ms |
| Turndown ratio | 1:100 |
| Interface | Touchscreen, Chinese / English |
| Application stage | Laboratory pilot / bench scale |
Need multi-component ratio delivery?
In addition to the standard single-component system, JONSN can customize dual-component, tri-component, and multi-component micro-flow control systems according to process requirements, supporting independent closed-loop and synchronized ratio control for each channel.
Customization development is supported for flow range, material, interface type, and communication protocol.
